Cost of repairing pull cord switch?

This sounds like the spring inside the pull cord has failed and requires replacing. Cost of pull and labour would be around £60

If it’s as simple as a faulty switch then it shouldn’t be more than £50 to swap

Investigation would be required to check for faulty connection, the electrical shower could be faulty, we would need to check the amp, check the circuit breaker and voltage and wire connections.

If a replacement is needed, the rough cost could be around £100 to £150.

80£

Replace the pull cord switch =£75
Pull cord isolator =£38

The pull cord is your problem, will Just Need replacing like for like , I would replace and install for £55

Hi it would be approximately £40 labour and materials

Yes sounds like a new pull cord is required. Part around 15 pounds and fitting around 50 pounds.

By the sounds of the description it’s the isolator to the shower.

It would cost around £75 for an electrician to come out and replace

It sounds like the pull cord is the issue. To replace the pull cord would be £12 plus 30 minutes labour. £37 total

hello a job like this should take max1 hour
id probably charge it out at 50/60 pound
for me to turn up basically !

£45 if local

To asses the fault, to replace the pull cord for like for like, should this be the problem, £50

Roughly what I would personally expect to pay to have a shower pull cord replaced is the cost of the pull switch itself plus £30 but some electricians may charge more and some may charge less. Prices will vary dependant on a tradesman’s travel distance and make of pull switch used etc.

Hi there,

The problem could be anything from a loose connection in the switch or even a faulty switch, not easy to tell without taking a look of course. I'd recommend having the switch changed, the materials should cost between £8-£15 and I'd estimate the labour and callout to cost about £40. In total I'd say for £50-£60 you could have your problem solved but that's specifically if the actual switch is faulty, the deeper the issue the more expensive it would be to fix unfortunately.

Hope this helps a little.

Thanks and good luck.

Materials will be around £20
Labour £40-£50

Hi, will need to check the Electrical first to see if any power going to pull cord. Rough estimate £60 to £200

Shower pull cord broken £60

£50 thanks

Faulty switch cord due to wear and tear, £5 for materials and £40 to change the switch. 20 minutes work.

Cost of new shower pull cord switch / £15
1 hour labour £25

Total £40

£25 + parts

Simple change to a new pull cord will cost you next to nothing

An Electrician can arrange a Call out appointment to investigate the fault for the shower circuit. The price will be £60/hr + materials (in case the pull cord switch has to be changed) + VAT

Including fitting it would be £80 with labour

Replace pull switch which would cost approx £50.00

This is a very quick and way fix, the cost of replacing your pull cord switch would be £40+VAT and materials

Depending on travel time. With part supplied £80

There usually mot repairable and cost of change it it’s 50£ plus parts

£85 plus materials

Roughly £100-£150

Probably the mechanism inside the pull cord switch is damaged I can supply and install basic pull cord switch £100.

Hi there , it’s Paul from pjg electrical there are a number of reasons why this may have occurred . First thing the size of the cable has to be adequate for the shower that has been installed . The switch might possibly have burnt out because of an overload on the cables . An insulation resistance test would have to be done on the cable assuming the cable size and circuit breaker are adequate enough , then the pullcord switch would need changed over as the mechanism in the switch may not be working . Then a check would be done to the shower unit to make sure the shower has 240 volts and the water is also flowing from the shower head .supply and fit of a new pullcord should be no more than £90 .

the only option to repair it is to replace it or move the wiring to the wall in the form of a switch - this is more useful.
Coming back to the full price, the exchange fee is 50 pounds

The issue with your pull cord switch for the Mira electric shower may be due to a faulty switch or wiring problem. The switch might need replacing. The cost to repair or replace a pull cord switch can vary but typically ranges from £60 to £100, including parts and labour. It's important to hire a qualified electrician to ensure the job is done safely and correctly. The electrician will check the wiring and replace the pull cord switch if necessary, restoring power to your shower unit.

From your description, the pull cord switch is the most likely cause. These switches can wear out over time, particularly on high-load circuits such as electric showers, and it's common for the internal contacts to fail so the switch no longer clicks or supplies power.

Before replacing the switch, an electrician should carry out a few basic checks to confirm that power is present at the switch, that the protective device hasn't tripped, and that there isn't another fault with the shower or wiring.

If it is just the pull cord switch, it's usually a straightforward repair. I would typically expect to charge £90–£150, including a quality replacement switch and labour, depending on location and whether it's during normal working hours. If testing identifies a fault with the shower unit or the wiring instead, the cost may be higher.

A qualified electrician will be able to diagnose the fault and, in many cases, complete the repair during the same visit.

Sounds like the switch needs replacing. Consider replacing with a fused switch mounted outside the bathroom

Hi there,

Pull cord switches do fail over time, the issue you are describing is a common issue. The issue could be with the switch mechanism itself, or also a conductor which has come loose and disconnected from its terminal, among other options.
Shower pull cord switches are not expensive (around £10-15 depending on the brand) so the cost of having it replaced it minimal.
I do recommend having it checked and, if necessary, replaced by a competent electrician.

Hi

It sounds to me like you just simply need to replace the shower pull switch because it has broken due to wear and tear. I would personally charge around £43.12 to replace it.

It sounds like the pull cord switch for your Mira electric shower has failed. These switches are often used to isolate the power to the shower for safety reasons, but when they stop working, it can prevent the shower from turning on.

Possible causes:
1. Faulty pull cord switch: Over time, the internal mechanism of the switch can wear out, or it may become jammed or damaged.
2. Loose or broken wiring: The connections within the pull cord switch may have become loose or disconnected.
3. Shower unit issue: While the issue seems to be with the pull cord switch, in rare cases, the problem might lie within the shower unit itself.

Cost to repair:
• Replacing the pull cord switch typically costs around £85 to £140, which includes the cost of the new switch and labour for installation.
• If there are additional issues, such as faulty wiring or issues within the shower unit, the cost could rise, and you may be looking at a price range closer to £150 or more.

Recommendation:
It’s best to have a qualified electrician inspect the issue. If you’re unsure about how to proceed, or if you’re not familiar with working with electrics, contacting a professional will ensure the repair is done safely and in compliance with regulations.

Let me know if you need any further assistance or would like to book a quote!

£70