Replace brick wall with wooden fence.

If the wall is bulging and starting to move, it’s definitely best to take it down rather than try to repair it, as it’s likely past its best.
Replacing it with a timber fence is a good, cost-effective option. For a 2m high fence over 7m, you’d be looking at installing new posts at around 1.8m centres, set in concrete for strength. I’d recommend either:
• Treated timber posts (budget option)
• Or concrete posts (longer lasting and more solid)
Panels or slatted fencing can then be fitted between depending on the look you’re after.
Just be aware at 2m height, you may need to check boundary rules or planning depending on location, especially if it’s front-facing.
Rough guide: • Removal and disposal of wall: £300–£800 depending on access
• New 2m fence supply & install: £700–£1,500
A fence will be much more forgiving than brickwork and far cheaper to install and maintain.

Replacing a 7m long, wobbly, bulging brick wall with a 2m high fence is a practical, cost-effective alternative to a rebuild. A 2m high fence provides a solid, secure boundary, with common options including feathered edge fencing (approx. £68 per panel) or wooden picket fencing for a rustic look.

.knock down brick wall by hand using sledge hammer ,there should be concrete base foundation left . youcan drill out into the base fitings that will hold fence postup rights then just put up fence . or dig out holes along side of foundation then put post in hole and fill with post mix /cement make sure the post are upright /plum and all are in line.once post are set allow a few days or evena eek to set prober and then fit that ju which just slot in yn which slot in to fencing panels to post by screws there a some panels which just slot in to posts .i can do all this for you let me know anytime

replacing the existing brick wall with a 2m high wooden fence is a practical and cost effective option. The brick wall would need to be safely taken down and removed, and the ground checked to ensure it is suitable for installing fence posts. For a fence this height, post would need to be properly set in concrete at the correct spacing to ensure stability, especially over a 7m length,. Depending on location and boundary rules, its also worth checking local planning guidance., as 2m is typically thr maximum height allowed without permission. Once installed correctly , a well built timber fence will provide good privacy and a neat finish without the cost of rebuilding a brick wall .

You can replace with a fence to exact same height as existing, we’ve done previously and customers have had concrete posts and gravel boards installed then bespoke fencing in between the posts

Given the condition you’ve described, taking the wall down and replacing it with a fence is a sensible and much more affordable option.

For a 7 m run at around 2 m high, the most cost-effective and reliable solution would usually be **pressure-treated timber fencing**. Concrete posts with concrete gravel boards and closeboard (feather edge) panels on top are a popular choice in the NE6 area because they cope well with uneven ground, last longer than timber posts, and keep costs down compared to rebuilding in brick. Once the unsafe wall is removed and the ground is levelled, posts can be set securely to deal with the unevenness you mentioned.

Before starting, it’s important to check whether the wall is on a boundary and whether planning rules apply. In most cases, a 2 m fence is permitted without planning permission, especially at the rear of a property, but it’s worth confirming with Newcastle City Council for peace of mind. If the wall borders a pavement or public area, extra care will be needed during removal for safety.

If you’d like, I can give you a rough cost estimate, suggest materials or explain how to phase the work to keep costs as low as possible.

Hi there,

Thanks for the details. If your brick wall is bulging and wobbly, it’s likely become unstable, so removing it is definitely the right move for safety reasons.

If you’re looking to replace it with a 2m high fence, that should be much more affordable and easier to maintain than rebuilding the wall. A few things to consider:

Safety first – Since the wall is unstable, it’s best to have it carefully taken down by someone with experience (a local builder or fencing contractor) to avoid any accidents.

Fence options – You could choose from timber, composite, or metal panels depending on the look and budget you’re going for. Timber tends to be the most cost-effective.

Planning permissions – In most cases, a fence up to 2m high at the rear of a property doesn’t need planning permission, but if it borders a public highway, it’s best to double-check with your local council.

Foundations or posts – Ask your contractor to inspect the existing foundation or footing; sometimes the old wall’s footing can be reused for fence posts, saving on cost.

If you’d like, I can help you find a few local contractors in the NE6 area who could give you quotes for safely removing the wall and installing a new fence.

Remove the bulging brick wall safely, then install a 2m high timber or composite fence with sturdy posts set in concrete. It’s cost-effective, durable, and can be styled to reflect the original wall’s presence.

Yes so firstly removal of the brick wall, will require a small skip hire to remove rubble, dig holes for fence posts then install posts and fencing using post mix to secure the posts